Cnc usb controller power supply driver#
Cnc usb controller power supply upgrade#
Cnc usb controller power supply pro#
Cnc usb controller power supply Offline#

Both cooling fans in the kit operate fine. The laser does not function at all, after following all available instructions.

Cnc usb controller power supply Offline#

Please make sure that you have unplugged the USB cable when using the offline control module and vice versa. The offline controller cannot be connected at the same time as the USB cable. I have read all the instructions and material I can find on the controller. The controller says it loads a file, but then nothing. The controller powers up and I am able to scroll through all of the menus, but I am unable to get it to move the cnc axis's.

Cnc usb controller power supply pro#

The 3018 PRO works fine, but I am having issues with the offline controller. The offline control module cannot move the axis.

Cnc usb controller power supply driver#

If the problem moves to the X axis, the X axis driver chip has the problem. If this doesnвЂ™t work Please swap the X axis motor and Y axis motor cables. The X-axis and Z-axis are Ok but the Y-axis does not move.Д¬heck the connections make sure it is plugged in correctly.Д¬heck that the axis is not binding by turning the screw by hand (disconnect the router first).Д¬heck that the grub screws on the coupler connecting the threaded rod to the stepper motor are tight and the coupler is not slipping. We suggest that you use our sample gcode to test it again. It seems like the spindle have some issues.Дoes the spindle motor turn on or turn off properly when you click the button вЂњspindle on/ offвЂќ? Can you use the slider to control the spindle speed? If the spindle speed can be controlled normally, we can confirm that the spindle motor doesnвЂ™t have any problems. I already tried to slow down the spindle to S200 and the F100 values. The spindle continues to rotate but it stops moving the axes: x, y, and z. When the spindle speed is too high and when you are already recording the machine stops. The spindle continues to rotate when the machine stops It should then move freely across the axis. Move the spindle mount all the way to the left by turning the threaded screw by hand and tighten the left hand screws, move the spindle mount to the right in the same way and tighten the right hand screws. The Y-axis bearings work perfectly for reference.Д¬heck the alignment of the guide rods and the threaded screw moving the axis, check the coupler between the stepper motor and the X-axis threaded screw is correctly aligned and slacken the screws holding the guide rods. When I test slide them with the shafts outside of the machine there is a ton of friction on them. I am having an issue with the X-axis linear bearings, they are binding extremely bad causing the machine to catch and jump at certain times. The offline controller and the USB cable cannot be connected at the same time. If the USB cable is connected correctly, the 5V indicator next to the RESET key will light up. Have one canвЂ™t get to work donвЂ™t know if the USB cables connected correctly.

Cnc usb controller power supply upgrade#

If the offline control module failed to control the machine, we suggest that you upgrade the firmware for the motherboard. Then use the offline control module to control the machine. Please check whether the USB port of the motherboard is loose or not. IвЂ™ve tried restarting, reinstalling the grbl software, and tried the reset button on the control board. The machine doesnвЂ™t show up on the com ports at all in either computer IвЂ™ve tried. Now no matter which usb port I try it will not connect. I have since tried it with two other computers and the offline controller which had worked fine when testing it earlier. I was able to assemble the machine and everything was working fine, but then in the middle of the sample carvings the machine lost connection. Make sure that you have installed the driver and selected the correct COM port. This is Windows saying it cannot connect to the router. When trying to connect, I get the вЂњserial port error 1: no such file or directoryвЂќ.